Radium Catch Can Kit (Crankcase Vent LH Mount) for BRZ FRS 86 (20-0102) *Discontinued*
The Radium Crankcase Vent Catch Can Kit for BRZ, FRS and 86 mounts on the left side of the engine bay to existing bolt holes. No modification of the vehicle is necessary. This kit does NOT vent to atmosphere (VTA), and is emissions and track legal.
*Discontinued*
As of June 2022, this part has been discontinued by Radium. We have none remaining in stock.
• See more BRZ Parts
Vehicle Fitment:
• 2012-2018+ Subaru BRZ
• 2013-2016 Scion FR-S
• 2012+ Toyota 86
(* Brake clearancing is necessary on RHD *)
Install Instructions:
Download PDF
Suggested for Install:
• Petcock Drain Kit
Full Description:
An oil catch can is essential on a performance vehicle to protect the engine from elevated levels of crankcase blow-by accumulated from aggressive driving. Excess oil-saturated air circulating back into the air intake stream can lead to degraded performance.
Benefits:
• Effectively raises the octane and increased engine performance from cleaner inlet air
• Prevents oil buildup in the intake or intercooler system walls, throttle body, intake manifold, etc.
• Excessive oil collection can be an indicator of a damaged engine.
• Lowers hydrocarbon emissions
Dimensions:
• Capacity: 6 fluid ounces
• Height (without fittings): 5 inches
• Outside Diameter: 2.45 inches
Single LH Crankcase Vent Catch Can Details:
The 20-0102 Crankcase Vent kit mounts on the left side of the engine bay. This catch can runs inline with the 1/2" breather port. At low loads it experiences atmospheric pressure, but when the engine is at high load (WOT), this hose will experience vacuum and would normally be drawing unwanted crankcase vapors, unspent fuel, and oil sludge into the air filter intake pipe. If the engine is turbocharged or supercharged and you are finding oil accumulation stuck in the intercooler, this catch can is a necessity as oil will lower the thermal efficiency properties of the heat exchange process.
Radium engineers have strategically located the catch cans for compatibility with both Right Hand Drive (RHD) and Left Hand Drive (LHD) "86" model variations. Some brake clearancing is necessary on RHD installations. Both of these kits are also compatible with all current aftermarket forced induction kits. For mounting, the kits use factory bosses and holes in the vehicle. No cutting, drilling or permanent modification to the vehicle is required.
This kit does NOT vent to atmosphere (VTA), thus is emissions and track legal. Closed loop systems route clean filtered air back in through the engine to be burned and to promote negative crankcase pressure for optimal performance. Furthermore, closed systems prevent unwanted oil vapors into the cabin.
Includes:
• Radium billet oil catch can with integrated condenser and dipstick
• Radium laser cut powder coated "86" specific mounting bracket
• Anodized aluminum banjo bolt, -8AN hose ends, and adapter fittings
• Enough hose to mate to custom applications
• Stainless steel mounting hardware
• Installation instructions
*Discontinued*
As of June 2022, this part has been discontinued by Radium. We have none remaining in stock.
• See more BRZ Parts
Vehicle Fitment:
• 2012-2018+ Subaru BRZ
• 2013-2016 Scion FR-S
• 2012+ Toyota 86
(* Brake clearancing is necessary on RHD *)
Install Instructions:
Download PDF
Suggested for Install:
• Petcock Drain Kit
Full Description:
An oil catch can is essential on a performance vehicle to protect the engine from elevated levels of crankcase blow-by accumulated from aggressive driving. Excess oil-saturated air circulating back into the air intake stream can lead to degraded performance.
Benefits:
• Effectively raises the octane and increased engine performance from cleaner inlet air
• Prevents oil buildup in the intake or intercooler system walls, throttle body, intake manifold, etc.
• Excessive oil collection can be an indicator of a damaged engine.
• Lowers hydrocarbon emissions
Dimensions:
• Capacity: 6 fluid ounces
• Height (without fittings): 5 inches
• Outside Diameter: 2.45 inches
Single LH Crankcase Vent Catch Can Details:
The 20-0102 Crankcase Vent kit mounts on the left side of the engine bay. This catch can runs inline with the 1/2" breather port. At low loads it experiences atmospheric pressure, but when the engine is at high load (WOT), this hose will experience vacuum and would normally be drawing unwanted crankcase vapors, unspent fuel, and oil sludge into the air filter intake pipe. If the engine is turbocharged or supercharged and you are finding oil accumulation stuck in the intercooler, this catch can is a necessity as oil will lower the thermal efficiency properties of the heat exchange process.
Radium engineers have strategically located the catch cans for compatibility with both Right Hand Drive (RHD) and Left Hand Drive (LHD) "86" model variations. Some brake clearancing is necessary on RHD installations. Both of these kits are also compatible with all current aftermarket forced induction kits. For mounting, the kits use factory bosses and holes in the vehicle. No cutting, drilling or permanent modification to the vehicle is required.
This kit does NOT vent to atmosphere (VTA), thus is emissions and track legal. Closed loop systems route clean filtered air back in through the engine to be burned and to promote negative crankcase pressure for optimal performance. Furthermore, closed systems prevent unwanted oil vapors into the cabin.
Includes:
• Radium billet oil catch can with integrated condenser and dipstick
• Radium laser cut powder coated "86" specific mounting bracket
• Anodized aluminum banjo bolt, -8AN hose ends, and adapter fittings
• Enough hose to mate to custom applications
• Stainless steel mounting hardware
• Installation instructions
See more Radium Products
 |
WARNING: Cancer and Reproductive Harm www.p65warnings.ca.gov |