STM Free Shipping to Continental USA

ETS Stock Location Turbo Kit for R35 GTR RHD

ETS

$13,084.00 
ETS-300-10-TK-06



This ETS turbo kit is for R35 GTR right hand drive models and places the turbos in the factory location. Packed with features like high flowing 1.9" runner manifolds, true merge collectors, stainless downpipes, TiAL MVR wastegates, high flow intercooler piping, heat shields and your choice of turbo.

Along with great performance, features such as an exhaust flex, t-bolt clamps, 4-ply silicone couplers and braided oil lines will all help make sure that you do not have to use the ETS Lifetime Warranty!

Vehicle Fitment:
2009+ Nissan R35 GT-R
• This kit fits RHD only (right hand drive vehicles)
See the LHD Kit HERE

Turbo Series: Horsepower Output (WHP):
GTX3076R Gen 2 850-1000 on pump
1200-1300 on race/e85
GTX3582R Gen 2 1000-1100 on pump
1400-1500 on race/e85

Features:
• 1.9" Runners
• Turbo S-Covers (4" Inlet)
• Choice of Turbo
• Choice of Inlet Size
• Choice of Downpipe Size
• Recirculated or Vent to Atmosphere Wastegate Route

Includes:
• 2x Manifolds
• 2x Turbochargers
• 2x Downpipes
• 2x Heat Shields
• 2x 44mm TiAL MVR Wastegates
• 2x Inlet Tubes
• Lower Intercooler Piping
• Oil Lines
• Water Lines

Large Runners - At 630cc per cylinder, the vr38 is 21% per cylinder larger than most 3.0l 6cyl and 2.0l 4cyl. On a cylinder to cylinder basis. To put a small runner on such a large cylinder is like putting a restrictor plate on the engine.

S Cover Turbos – Most kits on the market use what’s called a “Compact” cover turbo, or a hybrid turbo with either a Subaru, or Mitsubishi 20g housings. At low flow rates these housings work OK, but on anything over 800whp ETS feels that they are less than optimal compared to a true Garrett or “S” cover. The reason the S cover performs so much better is that they have a much larger diffuser area. This is the area where the air leaving the compressor wheel has time to slow down before leaving the compressor housing of the turbo. As the larger the area that the air is allowed to slow down in, the higher the pressure ration that the turbo can operate in. Also the lower the outlet temps will be.

Heat Shields – As the front of the GT-R is Aluminum, an unshielded kit can distort or weaken the front end of the vehicle. Also on the passenger side, the fuel lines must be kept cool for both the obvious fire reasons, but also to avoid tuning issues with a varying fuel density. Also if the fuel is allowed to get too hot, it can cause vapor lock issues at the inlets of very high flow pumps.
Pre-Assembled – Because of the very tight fitment of the R35 engine bay, ETS feels that the alignment of the kit must be perfect. The V-Band connections allow for a multitude of clocking positions, if not clocked perfectly, there could be many in and out attempts for install. This will cost either the shop or the customer excess money. To minimize this confusion, our kits come pre-assembled, with all water and oil lines installed. This will be a major labor savings at time of install.

Equal Length Runners – All cylinders, front to back and side to side have runners of a mean length of 12” =/- .300 This allows for precise tuning, crisper throttle response and less individual cylinder trimming. Also to compliment the 12” length which will work best 6500-8000 rpm, we use a moderately angled merge collector so there is a powerful scavenging effect to adjacent cylinders at the collector. This creates less back pressure at the exhaust valves and better overall breathing of the engine.

Wastegates in line with flow – With the very high flow rates of the new billet wheel turbo's, ETS has found the wastegate system must be very efficient, or else boost creep could be induced. As well a keeping run away boost under control, a very efficient wastegate system will allow tuners to start a tune at a much lower boost pressure, ensuring that the whole tuning process is done safely.

Factory Intake, IC pipe positions – Both the intakes and intercooler pipes terminate in factory positions, allowing the turbo kit to bolt up to your existing stock turbo intakes and Intercooler kits.

Down Pipes to factory locations – The High flowing 3.5” V band downpipes terminate at factory location allowing perfect connection to factory or aftermarket Y pipes. Downpipes are also bracketed to help locate the correct clocking outside the car. ETS also offers a 3.5" Y-pipe that goes to a single 4" connection. This is the perfect Y-pipe to get the absolute max from the PRO series turbo kit.

Critical Lines Away from heat – All of the Oil/Water lines are routed away from heat, down and around the turbos, instead of over and across the turbos. This will ensure a lifetime service life for these lines, while also lowering the temperatures of the fluids within the lines.

Support Brackets for Critical Lines – All Oil / Water lines are bracketed to prevent vibration or failures. This is extremely important for track vehicles, where high vibration and G forces can cause premature failure of unsupported lines.

Fully ported at every transition – From the head flanges to the exhaust flanges and even the PCV barbs in between, ETS prides themselves on the best craftsmanship and attention to detail in the industry. This means that all flanges are surfaced, all transitions ported, and all pieces are clean. These details may not make any major power differences, but it can be the difference in numbers such as 998 vs 1002 whp.

Lifetime Warranty – Full Lifetime warranty on all fabricated parts, and manufactures warranty on turbos through ETS

Shipping Times:
Most ETS products are built to order. Please allow 5-9 weeks for fabrication. California residents, please add 1-2 weeks for delivery.

Discounts:
We are sorry, discount codes are not available with ETS products.

See more ETS Parts
See more ETS Products
© All content is property of STM Tuned Inc
We price match!
If you find it cheaper, just give us a call!
(585) 226-8226


STM Boost Points!
Earn 1% back on all website purchases!
Sign up today!
© All content is property of STM Tuned Inc

We price match!
If you find it cheaper, just give us a call!
(585) 226-8226


STM Boost Points!
Earn 1% back on all website purchases!
Sign up today!



Customer Reviews

No reviews yet
0%
(0)
0%
(0)
0%
(0)
0%
(0)
0%
(0)

WARNING:
Cancer and Reproductive Harm
www.p65warnings.ca.gov