Save 10% on STM Products with code STM10

BLE Solid Conversion Lifter Kit for 4G63 (Set of 16) SLCMT00116



Vehicle Fitment:
1992-2006 Mitsubishi Evolution I-IX
1990-1999 1G & 2G DSM
(Eclipse GST/GSX, Talon TSi & Laser Turbo)

Full Set of 16 Lifters

The BLE Solid Lifter Conversion replaces the factory hydraulic lifters and comes with all necessary hardware for a straightforward installation. These Conversion Kits are perfect for anyone upgrading the factory valvetrain and/or camshafts.

The BLE Solid Lifters have specific enhancements over the factory and aftermarket hydraulic units. Only the finest 8620 Aerospace and 4130 chromoly steel is used to manufacture this product. Each assembly incorporates a fine-threaded lash adjuster, which features a radiused pivot head, built to exact OEM tolerances for use with the factory rocker arm. The lash adjuster is heat treated to increase surface hardness for maximum durability & wear resistance. It is locked in place to the lifter body using an 18-8 SS jam nut. The lifter body is cryogenically treated and its outside diameter is precision machined to match the cylinder head slot and oil passage clearances. Furthermore, the assembly is then chemically coated with black oxide for lubricity, corrosion protection, and improved wear & anti-galling characteristics.

The main reason BLE designed this product is pure and simple... Horsepower. A solid lifter valvetrain is more consistent, opens to a greater extent, and closes faster than a hydraulic setup. This translates into better control of the valvetrain, as well as more duration spent at higher flow valve lifts. In essence, more high rpm power is found by eliminating the physical "collapse" (and resulting power loss) experienced by hydraulic lifters at certain rpm thresholds and valve spring pressure levels. The stronger your valve springs, the sooner this collapse will occur with hydraulics! Likewise, fluctuations in oil pressure will affect the operation of your hydraulic lifters, not so with this solid lifter conversion. As a result, the BLE Solid Lifters allow for higher spring pressures to be run, as well as, more aggressive camshaft lifts. So go ahead, REV IT UP!

Drivability & the Dreaded "Lifter Tick":
Aside from the increased top-end horsepower and potential to turn your engine faster, drivability and low rpm power are also increased by closing the valves quicker and thus keeping cylinder pressures consistently higher. Your engine will even idle better and rid itself of the dreaded "lifter tic". The loud, obnoxious "tic, tic, tic...." you hear, when you start your car in the morning, is caused by excessive valve lash. Your hydraulic lifters are designed to eliminate all valve lash. However, after time, the internal mechanism gets dirty and/or begins to stick, thus preventing the rocker arm pivot from moving upwards to do its job. The problem can sometimes be induced by thicker oil weights, cold weather, or simply leaving your car parked for prolonged periods of time. The BLE Solid Lifters will set the valve lash to spec and keep it there until you decide to re-adjust it.

In race applications, where the engine is operated for shorter durations, and undergoes closer inspection intervals, a simple "splash" lubricated rocker pivot is acceptable. However, for street & daily operation, where constant surveillance is both unlikely and cumbersome, a steady flow of oil to the rocker is highly recommended for obvious reasons. With that said, the BLE Solid Lifters incorporate an oil feed with a restrictor to lube the rocker, while functioning similar to the "controlled" bleed of the OEM hydraulic units. Other solid units on the market, with unrestricted oil (passages) release the full pressure of the engine's oil system, which can effectively lower the oil pressure excessively.

- Made from the finest 4130 chromoly steel
- Manufactured to exact OEM dimensions
- Increased HP & valvetrain control at high RPM
- Fully adjustable - No need for shims (even with reground camshafts)
- Heat treated surface for maximum durability
- Black oxide conversion coated

Compatible Part Numbers:
SLCMT00324 / 
SLCMT00116 / MT00116

© All content is property of STM Tuned Inc

© All images are property of STM Tuned Inc

STM Boost Reward Points Earn 1% back on all website purchases! Sign up today!

Customer Reviews

Based on 2 reviews

Lifters - BLE Solid Conversion Kit - 4G63

1 x Lifters - BLE Solid Conversion Kit - 4G63

Tank you for Great service and fast shipping to Norway. Now i can get higher rpm and more power in my evo 8 usdm with 900+hp

Cancer and Reproductive Harm