AEM Infinity Series 5 Harness for Skyline RB26DETT (30-3515) *Discontinued*
AEM Infinity Series 5 plug and play harness is compatible with the R32/R33/R34 Skyline RB26DETT. This harness is for the Infinity 506 or 508 ECU. Connectors include aux port for ancillary sensors.
*Discontinued*
Unfortunately these have been discontinued by AEM. We have none remaining in stock.
Vehicle Fitment:
1989-1998 Nissan Skyline GT-R RB26DETT
• Manual Transmission
Includes:
(1) Harness
AEM Install Guide:
30-3515 PDF Install
More Info:
Once you have determined which Infinity ECU will best support your RB26DETT, you will need to purchase this 30-3515 Skyline Plug & Play adapter harness.
Includes a Wideband O2 connector, AEMnet connector for communication with other AEMnet enabled devices and an auxiliary connector with a High Performance DTM-Style 12P connector for adding common aftermarket sensors including fuel pressure, air inlet temperature, MAP, oil temperature and ethanol content sensor. The expansion port also includes a sensor ground, 5v reference, 12v power from relay and high side output for activating a relay or solenoid, a low side output for boost control and analog inputs for mode switch and no-lift shift.
The Infinity EMS delivers high-end engine control for the racing masses at a fraction of the cost. The Infinity Series 5 for Nissan SR20DET race engines is even more affordable than its larger Series 7 version because it is designed for smaller racing engines using low impedance injectors up to 6 cylinders or race engines driving up to 8 high impedance injectors. It features a smaller footprint than the Infinity Series 7 (5.855” x 5.55” x 1.8”) and a single, weatherproof 80-pin connector.
Complete Stand Alone Engine Control
The Infinity ECU combines with the Plug & Play harness to replace the factory ECU. It controls all of the engine functions and the Plug & Play wiring harness adapter eliminates the need for cutting and splicing wires.
Supports OEM Cam Angle Sensor
The AEM Infinity ECU supports the Nissan RB26DETT’s OEM Cam Angle Sensor (CAS) '360 Degree' pattern. The base calibration is pre-configured for the OEM CAS. The Infinity ECU can be reconfigured via the Setup Wizard to properly read the 12 crank/1 cam timing pattern on engines using an AEM CAS trigger disk.
Supports Factory VTC
The Infinity ECU supports the factory Nissan Valve Timing Control (N-VCT) system.
Signal Conditioner for ATTESA AWD System on R34 Skylines
The Infinity has a signal conditioner that ensures proper operation of the AWD system on R34 Skylines.
Read more about the Infinity and RB26DETT at aemelectronics.com
Discounts:
We are sorry, discount codes are not available for AEM products.
*Discontinued*
Unfortunately these have been discontinued by AEM. We have none remaining in stock.
Vehicle Fitment:
1989-1998 Nissan Skyline GT-R RB26DETT
• Manual Transmission
Includes:
(1) Harness
AEM Install Guide:
30-3515 PDF Install
More Info:
Once you have determined which Infinity ECU will best support your RB26DETT, you will need to purchase this 30-3515 Skyline Plug & Play adapter harness.
Includes a Wideband O2 connector, AEMnet connector for communication with other AEMnet enabled devices and an auxiliary connector with a High Performance DTM-Style 12P connector for adding common aftermarket sensors including fuel pressure, air inlet temperature, MAP, oil temperature and ethanol content sensor. The expansion port also includes a sensor ground, 5v reference, 12v power from relay and high side output for activating a relay or solenoid, a low side output for boost control and analog inputs for mode switch and no-lift shift.
The Infinity EMS delivers high-end engine control for the racing masses at a fraction of the cost. The Infinity Series 5 for Nissan SR20DET race engines is even more affordable than its larger Series 7 version because it is designed for smaller racing engines using low impedance injectors up to 6 cylinders or race engines driving up to 8 high impedance injectors. It features a smaller footprint than the Infinity Series 7 (5.855” x 5.55” x 1.8”) and a single, weatherproof 80-pin connector.
Complete Stand Alone Engine Control
The Infinity ECU combines with the Plug & Play harness to replace the factory ECU. It controls all of the engine functions and the Plug & Play wiring harness adapter eliminates the need for cutting and splicing wires.
Supports OEM Cam Angle Sensor
The AEM Infinity ECU supports the Nissan RB26DETT’s OEM Cam Angle Sensor (CAS) '360 Degree' pattern. The base calibration is pre-configured for the OEM CAS. The Infinity ECU can be reconfigured via the Setup Wizard to properly read the 12 crank/1 cam timing pattern on engines using an AEM CAS trigger disk.
Supports Factory VTC
The Infinity ECU supports the factory Nissan Valve Timing Control (N-VCT) system.
Signal Conditioner for ATTESA AWD System on R34 Skylines
The Infinity has a signal conditioner that ensures proper operation of the AWD system on R34 Skylines.
Read more about the Infinity and RB26DETT at aemelectronics.com
Discounts:
We are sorry, discount codes are not available for AEM products.
See more AEM Products
 |
WARNING: Cancer and Reproductive Harm www.p65warnings.ca.gov |